Performance of stud clusters in precast bridge decks/Inkaru grupes konstrukcine charakteristika surenkamosios perdangos tiltuose/Grupveida pretbidnu veiktspeja teraudbetona tiltos ar saliekamu dzelzsbetona klatni/Poltuhenduste kaitumine eelpingestatud silladekis.

Shim, Chang-Su ; Kim, Dong-Wook ; Nhat, Mai Xuan 等

1. Introduction

Full-depth precast decks for fast bridge construction are increasingly applied to composite bridges. Essentially, those bridges have many connections and their structural performance is crucial not only for structural efficiency but also for constructability. For those bridges, shear connections between precast slabs and steel girders typically draw a significant amount of attention from engineers. Shear connectors are embedded in filling material in a shear pocket and impart highly concentrated forces onto the bearing material. This concentrated force causes the concrete to fail in tension by embedment cracking, ripping, shear and splitting resulting in the decrease of ultimate strength of shear connection (Oehlers, Bradford 1995). Failure modes of the shear connection are guided according to the ratio of the shear strength of mechanical connectors and bearing material strength.

Stud connectors are the most common type of shear connectors used and need to be arranged according to the design provisions on minimum and maximum pitch requirements. Due to the constraints, rigid connection such as perfobond connectors is frequently used for high shear regions with small area for the connectors. However, it is difficult to use the rigid connector for the shear connection in precast decks because reinforcement details have difficulty to be accommodated near the shear pocket area or in the narrow joint area (Shim et al. 2001; Shim, Kim 2010; Tsujimura et al. 2000). Further, the strength of the connection is governed by shear strength of the concrete slab in these cases. To resolve these limitations, group stud shear connection with rather large studs was proposed and details for the connection have been investigated (Badie et al. 2002; Okada et al. 2006; Shim et al. 2004, 2007). The effective shear stiffness of the connection was proposed for the analysis of composite members (Marciukaitis et al. 2013; Shim et al. 2000).

For group stud shear connection in cast-in-place concrete slab, test results showed that the current design provisions are applicable for the ultimate strength and fatigue endurance when the minimum spacing was satisfied (Okada et al. 2006; Shim, Kim 2010). In their study, the effect of the group arrangement on static strength of stud shear connection was not observed because of strong concrete slab. All the specimens showed stud shank failure with minor damage of concrete slab. They also did parametric analyses and proposed shear strength reduction equations. However, those results were not verified through the experiment.

[FIGURE 1 OMITTED]

[FIGURE 2 OMITTED]

Stud shear connection in precast slab bridges, material properties of mortar in shear pockets and bedding layer should be considered for the evaluation of structural performance of stud shear connection (Shim et al. 2000). The thickness of the bedding layer generally varies along the bridge because of the section change and girder connection details. From the experiments on stud shear connection with those conditions, the ultimate strength of the shear connection in a precast deck was 75-101% of the tensile strength of the stud due to weaker bedding layer, and an empirical equation only for the stud shank failure was proposed. When the filling mortar has 1.5 times greater compressive strength than concrete for precast decks of minimum 35 MPa, the effect of compressive strength on the ultimate strength of the shear connection is negligible (Shim et al. 2001).

In order to accommodate new design trends of steel-concrete composite bridges with prefabricated concrete decks, large studs up to 31.8 mm diameter were experimentally investigated and availability of the current design provisions for stud shear connectors was verified based on the test results (Badie et al. 2002; Shim et al. 2004). Larose (2006) conducted experiments on stud clusters within a circular grout pocket. He reported that the confinement by a steel tube enhanced the shear strength of the grouped stud shear connection.

The failure modes of shear connection are categorized as shown in Fig. 1. Mode 1 is defined as stud failure without considerable concrete damage. Mode 3 means the concrete failure without stud failure. When the connectors are failed after considerable concrete damage, it is defined as Mode 2. When the post-cracking strength of the concrete slab is enough to resist shear strength of stud connectors, Mode 2 is expected. Therefore, it is necessary to increase shear strength of concrete slab to utilize the shear strength of stud clusters.

Recently, the full-depth precast decks have been increasingly applied to twin-girder bridges and open-box girder bridges. It reduces the construction cost by about 15-20% but several difficulties need to be solved. In order to satisfy the design requirements for composite action, it is necessary to place 6-8 shear pockets in each precast slab even when 25 mm studs are used. In a precast deck these pockets reduce the flexural stiffness resulting in cracking during delivery and erection process. The precast decks need longitudinal post-tensioning essentially and transverse pretensioning for wider decks (Shim, Chang 2003). Therefore, clustered stud arrangement of stud connectors is essential to solve the complex details. The previous empirical equation did not consider this case (Shim, Kim 2010).

Fig. 2 shows the typical examples of the shear connection detail dealt in this paper. Details of the deck are very complicated and need to be simplified by reducing the number of the shear pockets. One of the critical constraints for the simplification is the minimum pitch requirement of stud connectors in a shear pocket. The current minimum stud spacing is for shear connection in cast-in-place concrete slab. Maximum aggregate size and weld ability of the connectors using a welding gun are considered in this requirement. However, the shear connection for precast decks has high strength mortar around stud connectors. The minimum spacing is reduced only if the reduction of shear strength of the shear connection is considered. In order to reduce the number of shear pockets for the simpler details of precast slabs, it necessary to verify fatigue endurance of the connection for the reduced spacing. The reduction of static strength of the shear connection considering the reduced spacing does not significantly increase number of connectors because the fatigue endurance governs the design of shear connection.

In this paper the effects of the stud spacing on the static and fatigue performance were investigated. The group arrangement of stud connectors for prefabricated concrete slab was considered, including confining internal and external reinforcing bars to increase bearing strength and shear strength of the concrete slab, respectively. A new empirical equation for the clustered stud shear connection considering the reduced stud spacing was proposed. Fatigue tests were also conducted to verify the fatigue strength of group stud shear connection.

2. Experimental program

2.1. Static tests of shear connection

The experimental program consists of three series (G, GCIP, and S). G specimens deal with grouped stud shear connection for precast decks and GCIP for cast-in-place concrete decks (Shim, Kim 2010). The effect of stud spacing need to be estimated when concrete slab has a significant damage in bearing zone or splitting cracks in the direction of shear force, which is shown in Fig. 1b. S specimens had larger stud spacing in order to neglect effects of the group arrangement on static strength of shear connection. Table 1 summarizes the push-out specimens to investigate static behaviour of shear connection. In addition, previous test results (Shim et al. 2001) were used to evaluate the effects of the design parameters on static and fatigue strength of the shear connection.

Push-out specimens were fabricated to execute static tests for the evaluation of shear strength of shear connection with clustered stud arrangement. Fig. 3 shows the push-out specimen for precast decks. Precast decks with 250 mm thickness were prefabricated and were combined with steel beam by filling non-shrink mortar in shear pockets. Nine clustered studs with 25 mm and 22 mm diameter were welded on flanges and stud pitch was varied to have 5[d.sub.s], 4[d.sub.s] and 3[d.sub.s] ([d.sub.s] is stud diameter in mm). Even though the mortar fills the shear pocket with narrow space, it is impossible to allow the stud spacing less than 3[d.sub.s] due to the limitation on welding by a welding gun.

As mentioned before, it is necessary to prevent premature failure of bearing zone and concrete slab. In order to increase the strength of mortar and the shear strength of the concrete slab, constraining reinforcements were arranged inside and outside the shear pockets, as presented in Fig. 4. External reinforcements were placed before casting concrete of the precast slabs. Internal reinforcements were put in the shear pockets after placing the slab on a steel beam. Dimensions of the shear pocket were the same for all the specimens.

For the grouped stud shear connection in cast-in-place deck (GCIP specimens in Table 1) nine 25 mm studs are arranged to satisfy the minimum pitch requirements. Longitudinal and transverse spacing is 125 mm and 62.5 mm, respectively. To prevent severe damage of the concrete slab, 16 mm reinforcing bars are placed at the top and bottom concrete slab. The slab has 400 mm thickness and the design compressive strength of concrete is 40 MPa. Average compressive strength of concrete was 57.6 MPa resulting in minor damage in concrete slab. S22A and B specimens are for the single arrangement in precast decks. Stud spacing was thirteen times greater than stud shank diameter.

[FIGURE 3 OMITTED]

[FIGURE 4 OMITTED]

In order to ensure quality of cast-in-place mortar and enough strength for the bearing zone of studs, filling mortar had 1.5 times greater than the compressive strength of concrete for precast decks. From previous research (Shim et al. 2000), higher strength of mortar do not increase the shear strength of shear connection if the failure mode is stud shank failure. Yield strength of the reinforcement for all specimens is 450 MPa and tensile strength of stud connectors was 426 MPa.

Static tests of push-out specimens were performed in a hydraulic testing machine with a 10 000 kN capacity. Subsequent load increments were imposed such that failure does not occur in less than 15 min according to EN 1994-1:2004 Eurocode 4: Design of Composite Steel and Concrete Structures--Part 1: General Rules and Rules for Buildings. Longitudinal slips between each concrete slab and steel section were measured continually during loading or at each load increment using four 1/1000 mm LVDTs. The slip was measured at least until the load had dropped to 20% below the maximum load.

2.2. Fatigue tests of shear connection

Two sets of test specimens were fabricated to estimate the effect of stud spacing on the fatigue endurance of grouped stud shear connection, as presented in Table 2. Dimensions and material properties of the fatigue specimens were the same as those of static test specimens.

To assess the effect of grouped arrangement with reduced stud spacing, the previous experimental results on fatigue strength of shear connection were utilized (Lee et al. 2005; Shim et al. 2000, 2001). Among the test results, 25 mm stud connectors were selected for the comparison with current test results. FG25OS specimens had external reinforcements to strengthen the shear capacity of concrete slab.

3. Test results

3.1. Static behaviour of grouped stud shear connection

Two series of test specimens showed different failure modes according to relative strength ratio between concrete slab and stud connectors. Fig. 5 shows typical three failure modes of the shear connection from the static tests of G series.

Table 1 summarizes the test results in terms of shear strength, slip capacity and failure mode. Shear connection in a shear pocket showed behaviour of a block connector due to high strength mortar and internal reinforcements as shown in Figs 5c-5d. Mode 2 in Table 1 means that there was stud shank failure with severe cracking of concrete slab. Grouped stud shear connection with precast slabs had severe concrete cracking. Average shear strength of Push-out specimens with cast-in-place slab was 1.7 times greater than G25 specimens with the same stud spacing. Therefore, Eq (1) needs to be changed to consider concrete strength by using a common parameter of [square root of [f.sub.cm][E.sub.cm]] as specified in the design code EN 1994-1:2004. Instead of strength of concrete slab, the compressive strength of mortar ([f.sub.cm], N/[mm.sup.2]) should be included for the shear connection of precast decks.

[FIGURE 5 OMITTED]

For group stud connection of precast decks, closer pitch reduced the shear strength up to 30% when the failure mode is stud failure after concrete cracking of the slab. External reinforcements increased post-cracking strength of the concrete slab while internal reinforcement increased bearing strength a little. Therefore, it is important to strengthen the concrete slab when group stud connectors are used. When the failure mode is splitting failure of the concrete slab without stud failure, current design provisions on shear strength of concrete slab according to EN 1994-1:2004 are appropriate to evaluate the strength of the connection.

Fig. 6 represents the load-slip curves of the static test specimens. From the curves of 25 mm studs with stud spacing of 5 [d.sub.s], external and internal reinforcements showed 17.9% and 10% increase of the static strength respectively comparing to the specimens without additional reinforcement. The confining reinforcements increased the shear strength of concrete slab and bearing strength of mortar resulting in the change of failure mode from Mode 3 to Mode 2. For 25 mm studs with stud spacing of 3[d.sub.s], external and internal reinforcements showed 23% and 13% increase of the static strength, respectively. Shear connection with internal reinforcement showed stable behaviour after peak load. However, specimens with 22 mm studs showed negligible increase of shear strength by additional reinforcement. These specimens showed stud shank failure with minor damage in concrete slab.

[FIGURE 6 OMITTED]

Decrease of stud spacing from 5[d.sub.s] to 3[d.sub.s] reduced the shear strength of the shear connection by 7% for a standard specimen, 4.4% for internal reinforcing and 3.0% for external reinforcing. For the shear connection with 22 mm studs, the shear strength was reduced by 6.5% by decreasing the stud spacing from 4[d.sub.s] to 3[d.sub.s]. This reduction is considered to propose the empirical equation. Filling material in shear pockets for stud connectors is required to have greater compressive strength than that of concrete for precast decks (Shim et al. 2001). From the observation of the static tests, grouped stud shear connection including mortar in the pocket showed similar behaviour to a block connector. Therefore, it is more effective to strengthen the connection by placing confining reinforcement around the shear pocket.

Ultimate slip capacity of the shear connection is defined as the slip when the shear load is reduced by 10% from its peak (Oehlers, Bradford 1995). According to EN 1994-1:2004 a ductile connection is defined by the ultimate slip capacity greater than 6.0 mm. All the specimens which had Mode 1 failure showed enough slip capacity to ensure ductility of the connection, as summarized in Table 1.

3.2. Empirical equation for group stud shear connection in precast decks

In order to allow the particular design situation of closer stud spacing than the current design requirement, it is necessary to provide an empirical equation for static strength of the shear connection in precast decks. Previous test results on stud shear connection in precast slabs (Hanswille et al. 2007; Shim et al. 2000, 2001) were included in the analysis. As shown in Fig. 7, the empirical equation from the previous research (Shim et al. 2000) showed good agreement with test results of shear connection with wider stud spacing but overestimated the shear strength of the shear connection with clustered stud arrangement as presented in Fig. 7b. Therefore, an additional modification factor is needed to evaluate the effect of closer stud spacing.

[FIGURE 7 OMITTED]

In order to investigate the effect of stud spacing, the reference values were collected from the previous tests (Shim et al. 2000, 2001). The modification factor ([[beta].sub.s]) for stud spacing is assumed to be 1.0 when the pitch is wider than five times of stud shank diameter. An empirical Eq (1) for the reduction factor of stud spacing is proposed by linear regression analysis as shown in Fig. 8. When the stud pitch is smaller than 5 times of stud diameter, strength reduction of the shear connection is evaluated using the proposed equation. The equation only considers stud failure after concrete cracking. Therefore, it is necessary to check shear strength of concrete slab to utilize this equation.

[MATHEMATICAL EXPRESSION NOT REPRODUCIBLE IN ASCII], (1)

where s--pitch of stud connectors, mm; [d.sub.s]--the stud shank diameter, mm.

[FIGURE 8 OMITTED]

From the observation of static tests it is preferable to strengthen the concrete slab for group stud shear connection to ensure ductile behaviour and greater shear strength. Compressive strength of mortar should be 1.5 times greater than that of concrete slab in order to provide enough bearing strength. In actual precast decks, transverse reinforcements around shear pockets need to be checked to have enough shear strength to resist the grouped stud shear connection according to the design codes EN 1994-1:2004. Based on these two requirements, a new empirical equation for Mode 1 and Mode 2 failure is needed to consider structural characteristics of shear connection in precast decks. Even though the strengthening of concrete slab increases the shear strength of the shear connection, it is necessary to be considered as a detail requirement and a safety margin which is similar to the design codes.

Combining two empirical equations for the stud shear connection in precast decks an empirical model (4) was proposed to evaluate the shear strength considering filling material in shears pockets, bedding height and stud spacing. The equation assumes the failure Mode 2 and nonshrink mortar as a filling material in shear pockets. As specified in current design codes EN 1994-1:2004 the upper limit of the shear strength is:

[P.sub.Rd] = [[0.8[f.sub.u][pi][d.sup.2.sub.s]]/4] / [[gamma].sub.v], (2)

where [[gamma].sub.v]--partial safety factor; [d.sub.s]--diameter of the shank of the stud; [f.sub.u]--specified ultimate tensile strength of the material of the stud.

Instead of material properties of concrete, compressive strength and elastic modulus of mortar are used.

[P.sub.e] = [k.sub.c][P.sub.t] = [k.sub.c][[alpha].sub.b][[beta].sub.s][d.sup.2.sub.s][square root of [f.sub.cm][E.sub.cm]] (3)

where [[alpha].sub.b] = 1 - 0.0086([B.sub.h] - 20)--for bedding thickness effect; [[beta].sub.s]--for stud spacing effect as shown in Eq (1); [f.sub.cm]--compressive strength of mortar using a 50 mm cubic mould, MPa; [E.sub.cm] = 3.26 x [10.sup.3] [square root of [f.sub.cm]]--elastic modulus of mortar, MPa (Shim et al. 2000).

As mentioned before, shear strength of grouped stud shear connection in precast decks is lower than that of normal shear connection with cast-in-place concrete slab. Statistical analysis for the empirical equation was executed in accordance with Annex D of EN 1990:2002 Basis of Structural Design. Thirty eight test results of shear connection in precast decks including previous test results (Hanswille et al. 2007; Shim et al. 2000) were used for the analysis. As shown in Fig. 9, the factor [k.sub.c] of Eq (3) results to 0.22, while the current value in EN 1994-1:2004 is 0.29. The mean shear strength of the shear connection for precast decks was suggested as Eq (4) in the range of test parameters in this paper. The factor [k.sub.c] is determined according to test results used for the statistical analysis. Therefore, it is necessary to have more experimental data to propose a design equation based on Eq (4):

[P.sub.e]=0.22[[alpha].sub.b][[beta].sub.s][d.sup.2.sub.s][square root of [f.sub.cm][E.sub.cm]], (4)

where [[alpha].sub.b] = 1 - 0.0086([B.sub.h] - 20)--for bedding thickness effect; [[beta].sub.s]--for stud spacing effect as shown in Eq (1); [d.sub.s]--diameter of the shank of the stud; [f.sub.cm]--compressive strength of mortar using a 50 mm cubic mould, MPa; [E.sub.cm] = 3.26 x [10.sup.3] [square root of [f.sub.cm]]--elastic modulus of mortar, MPa (Shim et al. 2000).

The empirical equation for the clustered shear studs in precast decks will give 24% lower strength than the value from EN 1994-1:2004. It is necessary to design concrete slab to have enough shear strength to resist the ultimate shear strength of the clustered connectors by constraining reinforcements. The shear strength of the shear connection was increased through the use of higher strength mortar and confining reinforcing bars around shear pockets (Nguyen et al. 2009).

According to the test results by Larose (2006), stud clusters with steel tube confinement showed significant increase in shear strength of stud shear connection. A steel tube with 200 mm diameter and 1.6 mm thickness was used for the confinement of 16 mm stud connectors. 6 to 10 stud connectors were arranged in a shear pocket. Average cylinder strengths for the grout in shear pockets ranged from 48.7 MPa to 68.9 MPa. Fig. 10 shows the comparisons of test results and calculated values by Eq (3) according to different confinement methods. The results showed the extreme confinement increased the shear strength. Therefore, failure mode and its shear strength of grouped stud shear connection are effectively controlled by adding confinement as presented in Fig. 11 as an example design of a prefabricated prestressed concrete slab.

3.3. Fatigue endurance

Normally, the stud pitch is determined from the fatigue design. Minimum requirement for welding of studs using a stud gun is around 3ds. When the static failure mode of the shear connection is stud failure with negligible damage of concrete slab, fatigue endurance of the shear connection with group arrangement is expected to be similar to that of normal arrangement. Push-out specimens with cast-in-place concrete slab showed much higher fatigue strength than the current design codes (Shim, Kim 2010). As shown in Fig. 12a, the concrete damage was not overlapped and remained in a sound state after fatigue failure of stud connectors. Therefore, the current design provisions on fatigue strength of stud connectors are applicable to the design of the group stud shear connection when the minimum spacing is satisfied and concrete slab has enough strength to resist the shear load.

[FIGURE 9 OMITTED]

[FIGURE 10 OMITTED]

[FIGURE 11 OMITTED]

[FIGURE 12 OMITTED]

[FIGURE 13 OMITTED]

Damage overlapping of bearing zone was observed for the group stud shear connection in precast decks as presented in Figs 12b-12c. All the specimens had no shear failure of concrete slab. As stud spacing is closer, damage overlapping was significant and resulted in lower fatigue strength than the previous test results for normal arrangement (Shim et al. 2000). Damage in bearing zone of shear connection induces the higher stress concentration in weld collar of stud connectors.

Fig. 13 shows S-N curves of clustered stud shear connectors with closer spacing. Comparing with previous test results for single arrangement in a precast deck (Shim et al. 2001), clustered shear studs with closer spacing showed lower fatigue strength. However, the fatigue strength of the clustered studs in precast decks gave similar results from EN 1994-1:2004. However, it is essential to have careful considerations for the design of clustered shear studs in prefabricated slabs because the safety margin of fatigue endurance is decreased significantly judging from the test results. Without significant reduction of fatigue strength, it is possible to utilize the clustered shear studs for precast deck bridges when stud pitch is greater than 3[d.sub.s].

4. Conclusions

1. For the design of full-depth prefabricated concrete slabs, simplification of details in precast decks is crucial for the constructability. Considering filling material in shear pockets for clustered shear studs, it is possible to use closer stud spacing than the current design provisions. The effects of the stud spacing on the static and fatigue performance of shear connection in precast decks were investigated through tests and previous data. For the shear connection of precast deck bridges, the effects of the stud spacing and confining reinforcements were clearly observed. Decreasing the stud spacing resulted in a lower ultimate strength of the shear connection. For clustered stud connection of precast decks, closer spacing reduced the shear strength by up to 30% when the failure mode is stud failure after concrete cracking of the slab. The confining reinforcements inside and outside of the shear pocket enhanced the shear strength of the shear connection. It is more effective to strengthen the connection by placing confining reinforcement around the shear pocket.

2. The requirement of the minimum pitch for the stud connectors needs to be revised for precast decks. However, the shear connection with smaller spacing should have adequate reinforcement details to resist shear strength of group stud shear connectors. Considering filling material in shear pockets, bedding height and stud spacing, empirical equations for the evaluation of static performance of shear connection in precast decks were proposed.

3. Fatigue tests showed that the connectors in precast decks gave relatively lower fatigue strength than normal shear connection in cast-in-place concrete slab. In the range of test parameters of this paper, current S-N curves for the fatigue design of common stud connectors are applicable to the design of shear connection in precast decks.

4. Design recommendations on details were suggested to enhance the structural performance of shear connection in precast slabs. Reasonable safety margin is essential for the design of modular structures considering difficulties of quality control of connections in a construction field. Further experiments are needed to derive a design equation considering strengthening details such as high strength filling material and extreme confinement by a steel tube.

Caption: Fig. 1. Failure modes of shear connection: a--stud failure; b--stud failure after cracking; c--concrete failure

Caption: Fig. 2. Shear connection for precast deck

Caption: Fig. 3. Push-out specimens

Caption: Fig. 4. Details of confining reinforcement: a--external reinforcements; b--internal reinforcement

Caption: Fig. 5. Failure patterns of group stud shear connection in precast deck: a--G25OS-1 (Mode 1); b--GS25IS-2 (Mode 2); c--G25NS (Mode 3); d--effect of internal reinforcement

Caption: Fig. 6. Load-slip curves according to strengthening details: a--25 mm stud--3[d.sub.s], 5[d.sub.s]; b--22 mm stud--3[d.sub.s], 4[d.sub.s]

Caption: Fig. 7. Comparison of test results with previous empirical equation by Shim (2000): a--single arrangement of studs; b--group arrangement of studs

Caption: Fig. 8. Results of the statistical analysis

Caption: Fig. 9. Shear strength of group stud shear connection

Caption: Fig. 10. Comparisons of shear strength according to confinement methods

Caption: Fig. 11. Detail recommendation for shear connection in precast decks

Caption: Fig. 12. Fatigue failure pattern of group stud shear connection: a--FGCIP-3; b--FG25OS-1; c--FG25OS-4

Caption: Fig. 13. Fatigue test results of clustered shear studs in precast decks

doi:10.3846/bjrbe.2014.06

Received 12 December 2011; accepted 8 April 2013

Acknowledgement

This research was supported by a grant from the R&D Policy and Infrastructure Development Program (11-09-01-Development of Performance based design codes on steelconcrete composite structures) funded by the Ministry of Land, Infrastructure and Transport (MOLIT) of the Korean Government.

References

Badie, S.; Tadros, M. K.; Kakish, H. F.; Splittgerber, D. L.; Baishya, M. C. 2002. Large Shear Studs for Composite Action in Steel Bridge Girders, Journal of Bridge Engineering 7(3): 195-203. http://dx.doi.org/10.1061/(ASCE)1084-0702(2002)7:3(195)

Hanswille, G.; Porsch, M.; Ustundag, C. 2007. Resistance of Headed Studs Subjected to Fatigue Loading Part I: Experimental Study, Journal of Constructional Steel Research 63(4): 475-484. http://dx.doi.org/10.1016/jjcsr.2006.06.035

Larose, K. E. 2006. Performance of Shear Stud Clusters for Precast Concrete Bridge Deck Panels. Master Thesis 2006. University of British Columbia. 151 p.

Lee, P. G.; Shim, C. S.; Chang, S. P. 2005. Static and Fatigue Behavior of Large Stud Shear Connectors for Steel-Concrete Composite Bridges, Journal of Constructional Steel Research 61(9): 1270-1285. http://dx.doi.org/10.1016/jjcsr.2005.0L007

Marciukaitis, G.; Valivonis, J.; Jonaitis, B.; Kleiza, J.; Salna, R. 2013. Determination of Stiffness of the Connections of Composite Steel and Concrete Bridge Deck by the Limit Permissible Deflections, The Baltic Journal of Road and Bridge Engineering 8(1): 1-9. http://dx.doi.org/10.3846/bjrbe.2013.01

Oehlers, D. J.; Bradford, M. A. 1995. Composite Steel @ Concrete Structural Members: Fundamental Behavior. 1st edition. Oxford: Pergamon Press, 588 p. ISBN 0080419194.

Okada, J.; Yoda, T.; Lebet, J.-P. 2006. A Study of the Grouped Arrangements of Stud Connectors on Shear Strength Behavior, Journal of Structural Mechanics and Earthquake Engineering 23(1): 75-89. http://dx.doi.org/10.2208/jsceseee.23.75s

Shim, C. S.; Chung, C. H.; Kim, I. K.; Kim, Y. J. 2010. Development and Application of Precast Decks for Composite Bridges, Structural Engineering International 20(2): 126-133. http://dx.doi.org/10.2749/101686610791283623

Shim, C. S.; Kim, D. W. 2010. Structural Performance of Composite Joints Using Bent Studs, International Journal of Steel Structures 10(1): 1-13. http://dx.doi.org/10.1007/BF03249508

Shim, C. S.; Park, J. S.; Jeon, S. M.; Kim, D. W. 2007. Experimental Study on Group Stud Shear Connection, in Proc. of 5th International Conference on Advances in Steel Structures, vol. 3. Ed. by Richard, J. Y.; Choo, Y. S. December 5-7, 2007, Singapore: Research Publishing, 932-937.

Shim, C. S.; Lee, P. G.; Yoon, T. Y. 2004. Static Behavior of Large Stud Shear Connectors, Engineering Structures 26(12): 1853-1860. http://dx.doi.org/10.1016/j.engstruct.2004.07.011

Shim, C. S.; Chang, S. P. 2003. Cracking of Continuous Composite Beams with Precast Decks, Journal of Constructional Steel Research 59(2): 201-214. http://dx.doi.org/10.1016/S0143-974X(02)00032-9

Shim, C. S.; Chang, S. P.; Lee, P. G. 2001. Design of Shear Connection in Composite Steel and Concrete Bridges with Precast Decks, Journal of Constructional Steel Research 57(3): 203219. http://dx.doi.org/10.1016/S0143-974X(00)00018-3

Shim, C. S.; Kim, J. H.; Chung, C. H.; Chang, S. P. 2000. The Behavior of Shear Connection in Composite Beam with FullDepth Precast Slab, Structures and Buildings, the Institution of Civil Engineers 140(1): 101-110. http://dx.doi.org/10.1680/stbu.2000.140.L101

Tsujimura, T.; Shoji, A.; Noro, T.; Muroi, S. 2002. Experimental Study on a Joint in Prestressed Concrete Bridge with Steel Truss Web, in Proc. of the 1st Congress, Composite Structures Ed. by Japan Prestressed Concrete Engineering Association. October 13-19, 2002, Osaka: Osaka Prefectural Government, 347-352.

Chang-Su Shim (1) ([mail]), Dong-Wook Kim (2), Mai Xuan Nhat (3)

(1) School of Civil and Environmental Engineering, Urban Design and Study, Chung-Ang University, 84 Heukseok-Ro, Seoul, 156-756, Korea

(2,3) Dept of Civil Engineering, Chung-Ang University, 84 Heukseok-Ro, Seoul, 156-756, Korea

E-mails: (1) csshim@cau.ac.kr, (2) clearup7@cau.ac.kr, (3) nhatmaixuan@cau.ac.kr

Table 1. Static test specimen for precast decks

Specimen     [d.sub.s],    [f.sub.cm],    [f.sub.c]',
                 mm        N/[mm.sup.2]   N/[mm.sup.2]

G25NS            25            49.5           32.6
G25OS            25            49.5           32.6
G25IS            25            49.5           32.6
G25OS-1          25            49.5           32.6
G25NS-2          25            49.5           32.6
G25OS-2          25            49.5           32.6
G25IS-2          25            49.5           32.6
G22OS            22            49.5           32.6
G22IS            22            49.5           32.6
G22OS-1          22            49.5           32.6
G22IS-1          22            49.5           32.6
GCIP1-1          25             --            57.6
GCIP1-2          25             --            57.6
GCIP2-1          25             --            57.6
GCIP2-2          25             --            57.6
GCIP3-1          25             --            57.6
GCIP3-2          25             --            57.6
S22A             22           61.09           35.8
S22B             22           61.09           35.8

Specimen     [B.sub.h]      [Q.sub.u]       [[delta]
                 mm             kN        .sub.u], mm

G25NS            20           115.1           5.00
G25OS            20           135.6           3.60
G25IS            20           126.5          10.73
G25OS-1          20           105.1           3.52
G25NS-2          20           107.0           4.11
G25OS-2          20           131.6           3.61
G25IS-2          20           120.9           9.30
G22OS            20           119.9           6.67
G22IS            20           119.4           5.65
G22OS-1          20           110.9           7.56
G22IS-1          20           112.2          28.75
GCIP1-1          --           220.0          14.50
GCIP1-2          --           227.8          11.21
GCIP2-1          --           233.4          17.45
GCIP2-2          --           206.8          14.55
GCIP3-1          --           203.0          14.00
GCIP3-2          --           241.5          12.06
S22A             20           141.6           7.26
S22B             20           154.7           8.14

Specimen     S,              Details       Failure
             mm                             modes

G25NS                         No *         Mode 3
G25OS       5[d.sub.s]    Ext ** (D16)     Mode 2
G25IS                     Int *** (D10)    Mode 2
G25OS-1                     Ext(D16)       Mode 1
G25NS-2                        No          Mode 2
G25OS-2      3[d.sub.s]     Ext (D16)      Mode 2
G25IS-2                     Int (D10)      Mode 2
G22OS        4[d.sub.s]     Ext (D16)      Mode 1
G22IS                       Int (D10)      Mode 1
G22OS-1      3[d.sub.s]     Ext (D16)      Mode 1
G22IS-1                     Int (D10)      Mode 1
GCIP1-1                        No          Mode 1
GCIP1-2                        No          Mode 1
GCIP2-1      5[d.sub.s]     Ext (D16)      Mode 1
GCIP2-2                     Ext (D16)      Mode 1
GCIP3-1                    Ext (D16x2)     Mode 1
GCIP3-2                    Ext (D16x2)     Mode 1
S22A        13[d.sub.s]        No          Mode 1
S22B                           No          Mode 1

Notes: * No--no additional reinforcement; ** Ext--external
reinforcements added; *** Int--internal reinforcement added.

Table 2. Fatigue test specimens

Specimen      Compressive       Compressive        Stud
              strength of       strength of       spacing
              mortar, MPa      concrete, MPa

FG25OS-1         49.5              32.8         4[d.sub.s]
FG25OS-2         49.5              32.8         4[d.sub.s]
FG25OS-3         49.5              32.8         3[d.sub.s]
FG25OS-4         49.5              32.8         3[d.sub.s]
FGCIP-1           --               57.6         5[d.sub.s]
FGCIP-2           --               57.6         5[d.sub.s]
FGCIP-3           --               57.6         5[d.sub.s]

Specimen    Concrete slab    Reinforcement      Stress
                                 detail       range, MPa

FG25OS-1       Precast            Ext.            130
FG25OS-2       Precast            Ext.            150
FG25OS-3       Precast            Ext.            130
FG25OS-4       Precast            Ext.            150
FGCIP-1     Cast-in-place          No             140
FGCIP-2     Cast-in-place          No             150
FGCIP-3     Cast-in-place          No             160